Key Takeaways
- Volume-driven beat, margin expansion intact: Revenue grew 24% YoY as the largest customer gained market share, lifting EBITDA margin from 10.9% to 11.9%.
- The company is structurally outgrowing its market: A 4%+ revenue CAGR has doubled the market growth rate, driven by share gains at Ashok Leyland and a 20% export CAGR since FY19.
- Per-axle revenue is rising with vehicle content: India is manufacturing bigger, future-ready axles; tonnage already crossed the 2018 peak even though vehicle counts have not.
- Commodity is a pass-through, not a profit lever: A back-to-back system with customers insulates margins from raw material swings, leaving volume and cost control as the real drivers.
- What to watch next quarter: Whether the predicted flat-to-softer H2 MHCV volumes materialize, the pace of new product conversion (Tandem 160, deep mining axle, TLB axle), and any margin guidance beyond the constrained "Mission 25" framing.
Demand & Market Structure
- CV cycle entering a cautious phase: Management predicts ~3% FY24 industry growth, with a reasonably good H1 giving way to an almost flat H2; the range could widen to 10% depending on conditions.
- Election-year conservatism is a near-term drag: Fleet operators are conserving cash ahead of elections, and management expects conservative spending until mid-election sentiment shifts.
- K-type growth is the pattern: The market is growing but not at high rates; the company is capturing disproportionate share within that uneven expansion.
- MHCV volumes are already softening: OEM indications point to Q4 volumes lower YoY versus the prior year, and registrations have started declining this quarter.
- Long-term structural tailwinds remain: Government infrastructure push, vehicle scrappage policy gaining momentum, and India's trajectory toward a $5 trillion economy all support medium-term demand.
Muthukumar N: "While these are the positive factors that I can say, we have conservative numbers."
Competitive Position & Share Gains
- Market share has doubled over the last decade: While the commercial vehicle market is still 20% below its previous peak, Automotive Axles has grown 20% beyond it.
- First-mover in axle technology sustains leadership: The company was first to introduce hub reduction, axles with diff lock, and tandem axles in India over the last 10 years, maintaining its #1 position as an independent axle manufacturer.
- Time-to-market collapsed from years to months: New application development cycles dropped from 2-3 years to under one year, often under six months, because the JV partner (MHVSIL) brings product and technology ahead of time and provides validation infrastructure.
- Customer warranty demands have nearly doubled: Requirements moved from 100k km to 600k km (and 5,000 hours for tippers), demanding different manufacturing processes; NVH requirements for bus applications have also increased significantly.
- Conversion efficiency runs at double market growth: For every unit of top-line growth, EBITDA or PBT growth is almost double that rate.
Nagaraja G: "once upon a time, our time to market for a new application or a new product used to be anywhere between two years to three years and then in the last three years to four years, it has been dropped down to less than a year. In many a times, it is less than six months."
New Products & Pipeline
- Five products at various stages of development: The largest is the Tandem MT160 axle for 8x4 and 10x4 tipper applications; others include a Backhoe Loader axle under testing, new hub products, and upgraded RS120/145 axles for fuel-efficient, lightweight, higher-durability regional applications.
- Deep mining axle is ready for launch: Cummins Meritor has a design for both surface and deep mining; the protection axle for deep mining has completed testing with various OEMs.
- TLB axle is technically superior and being pitched to customers: The company developed a product for Tractor Loader Backhoe that it describes as very competitive, and is working with customers including an offer to JCB, which currently makes its own axles.
- New products are designed to cover requirements through 2030: Three or four products are being launched well ahead of market requirements to address next-generation vehicle needs.
- Global portfolio localization is a fast-follower advantage: Additional products available in the Cummins Meritor global portfolio can be localized, tested, and applied for specific requirements in a very short period.
Exports & Defense
- Exports have doubled since FY19 at a 20% CAGR: Management declined to disclose the absolute value or percentage split but offered the CAGR reference in response to repeated investor requests.
- Aatmanirbhar Bharat is the export expansion thesis: The company is trying to leverage the policy framework to expand exports, bringing in alternating technology, disruptive innovation, and value engineering.
- Defense is a long-term investment, not a near-term contributor: Five products are approved, and defense sales have grown at a 3-4% CAGR from a FY20 base, but development, validation, and testing costs are high.
- Defense conversion timing is unknowable: When approved products will convert to vehicle orders is, in management's words, an unanswerable question; the government has completed only 50% of its committed procurement through 2025.
- Automotive Axles does not supply axles to Bharat Forge for defense vehicles: Management confirmed this after an initial check, noting the difference between rigid axles and independent suspension.
Muthukumar N: "When it is going to convert the vehicle, when it is going to go, it is a million dollars question."
Margins & Cost Structure
- EBITDA margin expanded 100 bps YoY to 11.9%: The improvement was driven by volume growth, cost control, and the "Mission 25" cost-reduction program mitigating inflationary pressures.
- Commodity is fully pass-through, insulating margins: A back-to-back system with customers means the organization is not greatly impacted when commodity prices rise or fall, except for timing differences; commodity adds no margin at the bottom line.
- Inflationary pressure is broad-based but actively managed: Transportation cost, supplier conversion cost, and power cost are all rising; the company is bringing initiatives to mitigate and deliver over and above the inflationary impact.
- Depreciation is structurally low and will stay that way: As a 42-year-old organization, most assets are already depreciated; investments are selective, focused on new products and automations that give maximum benefit, and the company will not invest just because depreciation is low.
- Other income rose on improved treasury management: A new monitoring system for deposits and cash, interest income on surplus cash, and weekend parking in mutual funds for cash rotation are all contributing.
- Management declined to give a margin expansion timeline: When asked directly, the response was "I'm constrained not to share a number" and that they are not providing a briefing statement on where margins will end up.
Muthukumar N: "when the commodity went up, we have a very good system of a back-to-back with customers. And so, when the commodity goes up or comes down, our organization is not very greatly impacted except for the timing."
Capacity, Capex & Investment Philosophy
- Capex is set to double next year: From a current run-rate of ~INR10-20 crores, the company plans to invest for process automations, productivity, and process improvements, with a total range of INR60-70 crores between now and next year.
- Debottlenecking is planned for new technology and products: Over the next 1-2 years, significant improvements are planned to enhance current capacity to accommodate different product mixes and meet peak demands.
- The company invests ahead of the market, not behind it: Management explicitly stated it will not wait for the market to invest, citing 2018-19 investments that are still paying off today.
- Capacity utilization varies 10-15% with product mix: Manufacturing lines are lean and modular, so capacity depends on the monthly mix of tippers, line-haul trucks, and hub-reduction axles.
Muthukumar N: "never in our system, we will wait for the market to invest. Even in 2018-'19 what we invested is really helping us today."
Guidance & Commitments
| Commitment | Specifics | Timeline |
|---|---|---|
| Industry growth | ~3% FY24 growth, possibly up to 10% depending on conditions; H2 almost flat | FY24 |
| Capex | Double current run-rate; INR60-70 crores total between now and next year | Next year |
| Capacity enhancement | Significant improvements to accommodate different product mixes and peak demands | Next 1-2 years |
| Digitalization | 100% digitalization target | By 2028 |
| Solar power mix | Increase solar from 40% to 80% of overall power consumption | No date |
| New product coverage | Three to four products launched to cover next-generation requirements | Through 2030 |
| Defense procurement | Government committed procurement through 2025; only 50% completed so far | By 2025 |
Key Metrics
| Metric | Q2 FY24 |
|---|---|
| Revenue | ₹588 cr, +24% YoY |
| EBITDA | ~₹70 cr, +35% YoY |
| EBITDA margin | 11.9%, +100 bps YoY (10.9% in Q2 FY23) |
| PEBIT | ₹60.4 cr, +49% YoY (₹40.5 cr in Q2 FY23) |
| PEBIT margin | 10.3%, vs 8.5% in Q2 FY23 |
| YTD revenue | ₹1,122 cr, +15% YoY (₹977 cr in H1 FY23) |
| YTD EBITDA margin | 11.6%, vs 10.7% in H1 FY23 |
| YTD PEBIT | ₹111.2 cr, +35% YoY (₹82.1 cr in H1 FY23) |
| YTD PEBIT margin | 9.9%, vs 8.4% in H1 FY23 |
| Gross profit improvement | 0.5% YoY |
| Other expenses reduction | ~40 bps YoY |
| Other income | Almost doubled YoY, driven by surplus cash management |
| Depreciation | ₹89 (per an analyst's math), down from ₹103 in Sep 2022 |
| Capex guidance FY24 | ₹10–20 cr, sustenance-focused |
| Capex guidance FY25 | Doubling FY24 level, for automation and new products |
| Capacity utilization (axles) | 70–75%, varies by product mix |
| Capacity utilization (brakes) | 70–72% |
| Export CAGR (2018–19 to date) | 20%, exports doubled over the period |
| M&HCV industry growth outlook FY24 | 5–8% vs FY23 |
| M&HCV industry volume (FY19 peak) | 476,000 vehicles vs 407,000 currently |
| Renewable energy share target | 80% of power consumption |
| Solar power share (current) | 40% of overall power consumption |