Key Takeaways
- Resilient profit in a tough quarter: PBT held roughly flat YoY in H1 despite raw material cost spikes, with H1 PBT ~2.6% higher YoY even as sales were marginally lower.
- Inventory build-up signals future revenue: Inventory rose to ₹1,280 cr at H1 end, driven by high-value nickel alloys and Rohtak WIP, which management expects to convert into sales in coming months.
- Wide plate mill and Rohtak are the near-term growth levers: The wide plate mill is ramping through trials toward a ~₹500 cr peak revenue potential, while Rohtak began contributing in Q2 and targets ~₹100 cr this year.
- Margin pressure is acknowledged but not yet visible: Fixed-rate orders and rising raw material costs will pressure margins, though mitigation via efficiency and scrap recycling has contained the impact so far.
- What to watch next quarter: Whether the ₹1,280 cr inventory converts to sales as promised, the pace of wide plate mill and Rohtak revenue ramp in Q3/Q4, and any margin erosion as fixed-rate orders flow through.
Revenue Drivers: Wide Plate Mill & Rohtak
- Wide plate mill ramp: The mill is still under trial, producing products sequentially. Q1 saw little contribution; Q2 showed improvement; Q3 and Q4 are expected to see further revenue increases.
- Peak revenue target: Once fully established, the wide plate mill is expected to generate ~₹500 cr in revenue, though this could go higher if high-value orders with greater value addition are secured, depending on market scenario and execution capacity.
- Early wins: The company has successfully produced nickel-based super alloy plates using this setting and exported some, and developed nickel-based super alloys for desulfation units required by power plants, aiming to replace imports.
- Rohtak facility: Started contributing revenue only in Q2. Production includes armoring of ~70-80 vehicles (15 rolled out so far) and a jacket order for 1,500 units. Major revenue change expected from Q4 onwards as production progresses.
- Rohtak sales target: Targeting around ₹100 crores of sales from Rohtak this year; the order book exists but supply chain constraints are a limiting factor.
- Bulletproof jackets: Silicon carbide tiles with Carborundum are still in R&D developmental mode; if development is completed, significant requirements are expected from Paramilitary and Armed Forces.
Jha: "We have -- this is our estimation. See, our estimations we have kept like this. But higher is possibility is there, it can go higher also. But we cannot say right now, with the current market scenario and our execution capacity, we have given this figure."
Inventory & Margin Dynamics
- Inventory composition: The ₹1,280 cr inventory at H1 end is primarily driven by higher raw material costs (especially nickel) and increased stocking of high-value nickel-based alloys for super alloy production. WIP build-up at Rohtak also contributed, as some materials depend on imports and require inventory to maintain on-time production.
- Long conversion cycle: The average gestation from manufacturing to supply is 7-8 months because of the number of processing steps for precious materials, which explains the structurally high WIP.
- Margin pressure mechanics: Cost of production has risen due to raw material cost increases, while orders were taken at fixed rates from customers, creating margin pressure going forward.
- Mitigation so far: Margin pressure has not yet been reflected in results because of measures taken to reduce raw material consumption and improve efficiency, including more scrap recycling.
- Scrap management: Non-recyclable scrap is auctioned and sold; recyclable scrap is retained for internal use because it is high-value and provides good margins when reused in production. No write-offs are taken on scrap.
- Commodity price context: Commercial steel prices have declined, but MIDHANI does not use commodity steel in manufacturing. Prices of key raw materials (nickel, cobalt, moly, tantalum, iodine) have not come down; pressure on price persists as of today.
- No inventory readjustment: No inventory-related readjustment was taken in the income statement this quarter because raw material prices have not come down.
Jha: "I believe at the end I tell you this quarter two has been very, very difficult for us because the prices have gone up for all the commodities. In this situation maintaining the profitability has been a big challenge..."
Demand Environment & Order Book
- Defence sector tailwinds: Management sees the next four to five years as "very good" for the defence manufacturing industry, with MIDHANI expecting to grow on similar lines as other defence PSUs. Targets exist to double revenues over a four-year period, but require infrastructure upgrades, modernization, and investments.
- Order book expectation: Expect an order book of ₹1,500 crores to remain after the close of this assessment year.
- Missile segment: Astra missile induction is running at 100-150-200 per year, with corresponding orders being received. Akash missile material has already been supplied; fresh orders are needed for more.
- Space segment: Space launches are expected to pick up, with more than 300 satellites in queue with ISRO.
- Nuclear business: Nuclear projects are getting on fast track; new requirements for lattice tubes are expected. An order for super large pressurizer generator turbines is already being executed, and the company is participating in other orders.
- Sukhoi material Indianization: MIDHANI is working towards Indianizing material from Sukhoi (Russian origin); one successful development is expected to create opportunities for others.
- Su-30 MKI engine indigenization: MIDHANI is taking steps to indigenize critical alloys for the Su-30 engine, but clear business propositions depend on engine supplier permissions and contract terms. Management has no clear information on whether Indian materials will be allowed for MiG-29 engines.
Jha: "So India is looking for that sort of development, but it has not resulted in the clear cut in the business proposition. However, developmental work MIDHANI is your company is doing. We have taken some steps to indigenize the alloys, which are very critical for Su-30 engine."
NALCO JV: Re-evaluation Underway
- Project status: All clearances are in place: consent to establishment, pollution control approval, and Ministry of Environment and Forest clearance.
- Phase 1 progress: Tendering is over; the firm for first phase construction has been sought. The technology and equipment supplier has been finalized, and a consultant has been appointed for engineering procurement and management systems for civil construction.
- Phase 2 readiness: All tender documents for Phase 2 are ready; the moment Phase 1 is clear, Phase 2 will be in place for tender.
- Re-evaluation trigger: The project evaluation was done four years back. Management believes this is the right time to re-evaluate in the current world scenario to assess whether the return on investment remains attractive.
- Investment decision timeline: Expect to receive the right inputs from consultants in a couple of months. If inputs are encouraging, the project will be taken up fast, but clarity is needed before going to the board for investment approval.
Jha: "Since project evaluation was done four years back to get the certain amount of return on investment, we thought this is the right time we should re-evaluate that in the current world scenario and then take a call whether we should invest or not."
New Products, Certifications & Exports
- Defexpo launches: Six new products were launched at the recently concluded Defexpo, including super alloy nickel-based alloy sheets.
- Boeing MoU: A business cooperation agreement was signed with Boeing in the area of raw materials used in manufacturing, during the Defexpo.
- LCA certification: Most items supplied for LCA are already certified; certification is awaited for only two or three items. Management declined to predict the potential order size, stating values are difficult to estimate because there is no clarity on how much equipment the services will order, and the items are not exclusive to LCA.
- Export certification: Work is in progress; the company expects to start receiving certifications by mid-next year, not by this year-end.
- Export constraints: Good potential exists but is constrained by payment conditions and pricing. Customers are asking for grade-based supply systems, which is currently not acceptable; the company is exploring alternatives to meet customer expectations.
- Titanium business: MIDHANI has 25-30 years of expertise in titanium alloys with complete process control. Raw material (titanium sponge) is currently imported due to lack of domestic manufacturing at economic scale, as the requirement is only 800 tonnes.
Jha: "So right now, these values are difficult to predict because their project also, there is no clarity that how much of the equipment they are going to get the orders from the services."
Guidance & Commitments
| Commitment | Specifics | Timeline |
|---|---|---|
| Inventory conversion | Current inventory build-up to translate into sales | Coming months |
| FY23 internal sales target | ₹1,000 cr | FY23 |
| Wide plate mill ramp | Revenue increases expected; peak ~₹500 cr | Q3 and Q4 ramp; full establishment undated |
| Rohtak facility revenue | Major revenue change expected; targeting ~₹100 cr this year | Q4 onwards |
| Export certifications | Start receiving certifications | Mid-next year |
| NALCO JV investment decision | Re-evaluate returns; take up fast if encouraging | Couple of months for consultant inputs |
| EBITDA margin | Maintain 30%-33% with available product mix | Ongoing, subject to raw material cost pressure |
| Revenue doubling | Double revenues over a four-year period, subject to infrastructure upgrades and investments | Four-year horizon |
Key Metrics
| Metric | Q2 FY23 |
|---|---|
| Value of Production growth | ~41% YoY |
| PBT growth (H1 FY23) | ~2.6% YoY |
| Inventory | ₹1,280 cr at H1 FY23 end, up from ₹1,091 cr at FY22 end and ~₹800 cr at FY21 end |
| FY23 internal sales target | ₹1,000 cr |
| Order book | ₹1,500 cr as of Q2 FY23, expected to remain at this level after the assessment year |
| Order book: defense share | 40% to 55% |
| Order book: space share | ~35% |
| Order book: armour share | ~3% to 4% |
| Wide plate mill peak revenue potential | ~₹500 cr at full utilization |
| Rohtak facility FY23 sales target | ~₹100 cr |
| Rohtak facility: vehicles in production for armoring | ~70–80 vehicles, 15 rolled out |
| Rohtak facility: jacket order | 1,500 units to execute |
| Missile sector revenue (FY22) | ₹12 cr, similar expected in FY23 |
| Gross block | ₹937 cr presently, expected to reach ₹1,100 cr by year-end |
| Total assets | ~₹2,900 cr, expected ~₹3,000 cr by year-end |
| Asset turnover (on total assets) | 35%–40% expected |
| NALCO JV total investment | ₹4,000 cr |
| Scrap theft intercepted | 950 kgs by CBI |